Linux » Linux Kernel : Security Vulnerabilities, CVEs, CVSS score between 4 and 6.99

In the Linux kernel, the following vulnerability has been resolved: usb: ulpi: Fix debugfs directory leak The ULPI per-device debugfs root is named after the ulpi device's parent, but ulpi_unregister_interface tries to remove a debugfs directory named after the ulpi device itself. This results in the directory sticking around and preventing subsequent (deferred) probes from succeeding. Change the directory name to match the ulpi device.

In the Linux kernel, the following vulnerability has been resolved: PCI: Fix active state requirement in PME polling The commit noted in fixes added a bogus requirement that runtime PM managed devices need to be in the RPM_ACTIVE state for PME polling. In fact, only devices in low power states should be polled. However there's still a requirement that the device config space must be accessible, which has implications for both the current state of the polled device and the parent bridge, when present. It's not sufficient to assume the bridge remains in D0 and cases have been observed where the bridge passes the D0 test, but the PM state indicates RPM_SUSPENDING and config space of the polled device becomes inaccessible during pci_pme_wakeup(). Therefore, since the bridge is already effectively required to be in the RPM_ACTIVE state, formalize this in the code and elevate the PM usage count to maintain the state while polling the subordinate device. This resolves a regression reported in the bugzilla below where a Thunderbolt/USB4 hierarchy fails to scan for an attached NVMe endpoint downstream of a bridge in a D3hot power state.

In the Linux kernel, the following vulnerability has been resolved: scsi: Revert "scsi: fcoe: Fix potential deadlock on &fip->ctlr_lock" This reverts commit 1a1975551943f681772720f639ff42fbaa746212. This commit causes interrupts to be lost for FCoE devices, since it changed sping locks from "bh" to "irqsave". Instead, a work queue should be used, and will be addressed in a separate commit.

In the Linux kernel, the following vulnerability has been resolved: Revert "drm/amd: flush any delayed gfxoff on suspend entry" commit ab4750332dbe ("drm/amdgpu/sdma5.2: add begin/end_use ring callbacks") caused GFXOFF control to be used more heavily and the codepath that was removed from commit 0dee72639533 ("drm/amd: flush any delayed gfxoff on suspend entry") now can be exercised at suspend again. Users report that by using GNOME to suspend the lockscreen trigger will cause SDMA traffic and the system can deadlock. This reverts commit 0dee726395333fea833eaaf838bc80962df886c8.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Reset IH OVERFLOW_CLEAR bit Allows us to detect subsequent IH ring buffer overflows as well.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix incorrect mpc_combine array size [why] MAX_SURFACES is per stream, while MAX_PLANES is per asic. The mpc_combine is an array that records all the planes per asic. Therefore MAX_PLANES should be used as the array size. Using MAX_SURFACES causes array overflow when there are more than 3 planes. [how] Use the MAX_PLANES for the mpc_combine array size.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix dcn35 8k30 Underflow/Corruption Issue [why] odm calculation is missing for pipe split policy determination and cause Underflow/Corruption issue. [how] Add the odm calculation.

In the Linux kernel, the following vulnerability has been resolved: drm/nouveau: fix several DMA buffer leaks Nouveau manages GSP-RM DMA buffers with nvkm_gsp_mem objects. Several of these buffers are never dealloced. Some of them can be deallocated right after GSP-RM is initialized, but the rest need to stay until the driver unloads. Also futher bullet-proof these objects by poisoning the buffer and clearing the nvkm_gsp_mem object when it is deallocated. Poisoning the buffer should trigger an error (or crash) from GSP-RM if it tries to access the buffer after we've deallocated it, because we were wrong about when it is safe to deallocate. Finally, change the mem->size field to a size_t because that's the same type that dma_alloc_coherent expects.

In the Linux kernel, the following vulnerability has been resolved: x86/xen: Add some null pointer checking to smp.c kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Ensure the allocation was successful by checking the pointer validity.

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix fortify source warning while accessing Eth segment ------------[ cut here ]------------ memcpy: detected field-spanning write (size 56) of single field "eseg->inline_hdr.start" at /var/lib/dkms/mlnx-ofed-kernel/5.8/build/drivers/infiniband/hw/mlx5/wr.c:131 (size 2) WARNING: CPU: 0 PID: 293779 at /var/lib/dkms/mlnx-ofed-kernel/5.8/build/drivers/infiniband/hw/mlx5/wr.c:131 mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] Modules linked in: 8021q garp mrp stp llc rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) mlx5_ib(OE) ib_uverbs(OE) ib_core(OE) mlx5_core(OE) pci_hyperv_intf mlxdevm(OE) mlx_compat(OE) tls mlxfw(OE) psample nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables libcrc32c nfnetlink mst_pciconf(OE) knem(OE) vfio_pci vfio_pci_core vfio_iommu_type1 vfio iommufd irqbypass cuse nfsv3 nfs fscache netfs xfrm_user xfrm_algo ipmi_devintf ipmi_msghandler binfmt_misc crct10dif_pclmul crc32_pclmul polyval_clmulni polyval_generic ghash_clmulni_intel sha512_ssse3 snd_pcsp aesni_intel crypto_simd cryptd snd_pcm snd_timer joydev snd soundcore input_leds serio_raw evbug nfsd auth_rpcgss nfs_acl lockd grace sch_fq_codel sunrpc drm efi_pstore ip_tables x_tables autofs4 psmouse virtio_net net_failover failover floppy [last unloaded: mlx_compat(OE)] CPU: 0 PID: 293779 Comm: ssh Tainted: G OE 6.2.0-32-generic #32~22.04.1-Ubuntu Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] Code: 0c 01 00 a8 01 75 25 48 8b 75 a0 b9 02 00 00 00 48 c7 c2 10 5b fd c0 48 c7 c7 80 5b fd c0 c6 05 57 0c 03 00 01 e8 95 4d 93 da <0f> 0b 44 8b 4d b0 4c 8b 45 c8 48 8b 4d c0 e9 49 fb ff ff 41 0f b7 RSP: 0018:ffffb5b48478b570 EFLAGS: 00010046 RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffb5b48478b628 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffb5b48478b5e8 R13: ffff963a3c609b5e R14: ffff9639c3fbd800 R15: ffffb5b480475a80 FS: 00007fc03b444c80(0000) GS:ffff963a3dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000556f46bdf000 CR3: 0000000006ac6003 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? show_regs+0x72/0x90 ? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] ? __warn+0x8d/0x160 ? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] ? report_bug+0x1bb/0x1d0 ? handle_bug+0x46/0x90 ? exc_invalid_op+0x19/0x80 ? asm_exc_invalid_op+0x1b/0x20 ? mlx5_ib_post_send+0x191b/0x1a60 [mlx5_ib] mlx5_ib_post_send_nodrain+0xb/0x20 [mlx5_ib] ipoib_send+0x2ec/0x770 [ib_ipoib] ipoib_start_xmit+0x5a0/0x770 [ib_ipoib] dev_hard_start_xmit+0x8e/0x1e0 ? validate_xmit_skb_list+0x4d/0x80 sch_direct_xmit+0x116/0x3a0 __dev_xmit_skb+0x1fd/0x580 __dev_queue_xmit+0x284/0x6b0 ? _raw_spin_unlock_irq+0xe/0x50 ? __flush_work.isra.0+0x20d/0x370 ? push_pseudo_header+0x17/0x40 [ib_ipoib] neigh_connected_output+0xcd/0x110 ip_finish_output2+0x179/0x480 ? __smp_call_single_queue+0x61/0xa0 __ip_finish_output+0xc3/0x190 ip_finish_output+0x2e/0xf0 ip_output+0x78/0x110 ? __pfx_ip_finish_output+0x10/0x10 ip_local_out+0x64/0x70 __ip_queue_xmit+0x18a/0x460 ip_queue_xmit+0x15/0x30 __tcp_transmit_skb+0x914/0x9c0 tcp_write_xmit+0x334/0x8d0 tcp_push_one+0x3c/0x60 tcp_sendmsg_locked+0x2e1/0xac0 tcp_sendmsg+0x2d/0x50 inet_sendmsg+0x43/0x90 sock_sendmsg+0x68/0x80 sock_write_iter+0x93/0x100 vfs_write+0x326/0x3c0 ksys_write+0xbd/0xf0 ? do_syscall_64+0x69/0x90 __x64_sys_write+0x19/0x30 do_syscall_ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: x86/mm: Disallow vsyscall page read for copy_from_kernel_nofault() When trying to use copy_from_kernel_nofault() to read vsyscall page through a bpf program, the following oops was reported: BUG: unable to handle page fault for address: ffffffffff600000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 3231067 P4D 3231067 PUD 3233067 PMD 3235067 PTE 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 1 PID: 20390 Comm: test_progs ...... 6.7.0+ #58 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) ...... RIP: 0010:copy_from_kernel_nofault+0x6f/0x110 ...... Call Trace: <TASK> ? copy_from_kernel_nofault+0x6f/0x110 bpf_probe_read_kernel+0x1d/0x50 bpf_prog_2061065e56845f08_do_probe_read+0x51/0x8d trace_call_bpf+0xc5/0x1c0 perf_call_bpf_enter.isra.0+0x69/0xb0 perf_syscall_enter+0x13e/0x200 syscall_trace_enter+0x188/0x1c0 do_syscall_64+0xb5/0xe0 entry_SYSCALL_64_after_hwframe+0x6e/0x76 </TASK> ...... ---[ end trace 0000000000000000 ]--- The oops is triggered when: 1) A bpf program uses bpf_probe_read_kernel() to read from the vsyscall page and invokes copy_from_kernel_nofault() which in turn calls __get_user_asm(). 2) Because the vsyscall page address is not readable from kernel space, a page fault exception is triggered accordingly. 3) handle_page_fault() considers the vsyscall page address as a user space address instead of a kernel space address. This results in the fix-up setup by bpf not being applied and a page_fault_oops() is invoked due to SMAP. Considering handle_page_fault() has already considered the vsyscall page address as a userspace address, fix the problem by disallowing vsyscall page read for copy_from_kernel_nofault().

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix data races when accessing the reserved amount of block reserves At space_info.c we have several places where we access the ->reserved field of a block reserve without taking the block reserve's spinlock first, which makes KCSAN warn about a data race since that field is always updated while holding the spinlock. The reports from KCSAN are like the following: [117.193526] BUG: KCSAN: data-race in btrfs_block_rsv_release [btrfs] / need_preemptive_reclaim [btrfs] [117.195148] read to 0x000000017f587190 of 8 bytes by task 6303 on cpu 3: [117.195172] need_preemptive_reclaim+0x222/0x2f0 [btrfs] [117.195992] __reserve_bytes+0xbb0/0xdc8 [btrfs] [117.196807] btrfs_reserve_metadata_bytes+0x4c/0x120 [btrfs] [117.197620] btrfs_block_rsv_add+0x78/0xa8 [btrfs] [117.198434] btrfs_delayed_update_inode+0x154/0x368 [btrfs] [117.199300] btrfs_update_inode+0x108/0x1c8 [btrfs] [117.200122] btrfs_dirty_inode+0xb4/0x140 [btrfs] [117.200937] btrfs_update_time+0x8c/0xb0 [btrfs] [117.201754] touch_atime+0x16c/0x1e0 [117.201789] filemap_read+0x674/0x728 [117.201823] btrfs_file_read_iter+0xf8/0x410 [btrfs] [117.202653] vfs_read+0x2b6/0x498 [117.203454] ksys_read+0xa2/0x150 [117.203473] __s390x_sys_read+0x68/0x88 [117.203495] do_syscall+0x1c6/0x210 [117.203517] __do_syscall+0xc8/0xf0 [117.203539] system_call+0x70/0x98 [117.203579] write to 0x000000017f587190 of 8 bytes by task 11 on cpu 0: [117.203604] btrfs_block_rsv_release+0x2e8/0x578 [btrfs] [117.204432] btrfs_delayed_inode_release_metadata+0x7c/0x1d0 [btrfs] [117.205259] __btrfs_update_delayed_inode+0x37c/0x5e0 [btrfs] [117.206093] btrfs_async_run_delayed_root+0x356/0x498 [btrfs] [117.206917] btrfs_work_helper+0x160/0x7a0 [btrfs] [117.207738] process_one_work+0x3b6/0x838 [117.207768] worker_thread+0x75e/0xb10 [117.207797] kthread+0x21a/0x230 [117.207830] __ret_from_fork+0x6c/0xb8 [117.207861] ret_from_fork+0xa/0x30 So add a helper to get the reserved amount of a block reserve while holding the lock. The value may be not be up to date anymore when used by need_preemptive_reclaim() and btrfs_preempt_reclaim_metadata_space(), but that's ok since the worst it can do is cause more reclaim work do be done sooner rather than later. Reading the field while holding the lock instead of using the data_race() annotation is used in order to prevent load tearing.

In the Linux kernel, the following vulnerability has been resolved: perf: RISCV: Fix panic on pmu overflow handler (1 << idx) of int is not desired when setting bits in unsigned long overflowed_ctrs, use BIT() instead. This panic happens when running 'perf record -e branches' on sophgo sg2042. [ 273.311852] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098 [ 273.320851] Oops [#1] [ 273.323179] Modules linked in: [ 273.326303] CPU: 0 PID: 1475 Comm: perf Not tainted 6.6.0-rc3+ #9 [ 273.332521] Hardware name: Sophgo Mango (DT) [ 273.336878] epc : riscv_pmu_ctr_get_width_mask+0x8/0x62 [ 273.342291] ra : pmu_sbi_ovf_handler+0x2e0/0x34e [ 273.347091] epc : ffffffff80aecd98 ra : ffffffff80aee056 sp : fffffff6e36928b0 [ 273.354454] gp : ffffffff821f82d0 tp : ffffffd90c353200 t0 : 0000002ade4f9978 [ 273.361815] t1 : 0000000000504d55 t2 : ffffffff8016cd8c s0 : fffffff6e3692a70 [ 273.369180] s1 : 0000000000000020 a0 : 0000000000000000 a1 : 00001a8e81800000 [ 273.376540] a2 : 0000003c00070198 a3 : 0000003c00db75a4 a4 : 0000000000000015 [ 273.383901] a5 : ffffffd7ff8804b0 a6 : 0000000000000015 a7 : 000000000000002a [ 273.391327] s2 : 000000000000ffff s3 : 0000000000000000 s4 : ffffffd7ff8803b0 [ 273.398773] s5 : 0000000000504d55 s6 : ffffffd905069800 s7 : ffffffff821fe210 [ 273.406139] s8 : 000000007fffffff s9 : ffffffd7ff8803b0 s10: ffffffd903f29098 [ 273.413660] s11: 0000000080000000 t3 : 0000000000000003 t4 : ffffffff8017a0ca [ 273.421022] t5 : ffffffff8023cfc2 t6 : ffffffd9040780e8 [ 273.426437] status: 0000000200000100 badaddr: 0000000000000098 cause: 000000000000000d [ 273.434512] [<ffffffff80aecd98>] riscv_pmu_ctr_get_width_mask+0x8/0x62 [ 273.441169] [<ffffffff80076bd8>] handle_percpu_devid_irq+0x98/0x1ee [ 273.447562] [<ffffffff80071158>] generic_handle_domain_irq+0x28/0x36 [ 273.454151] [<ffffffff8047a99a>] riscv_intc_irq+0x36/0x4e [ 273.459659] [<ffffffff80c944de>] handle_riscv_irq+0x4a/0x74 [ 273.465442] [<ffffffff80c94c48>] do_irq+0x62/0x92 [ 273.470360] Code: 0420 60a2 6402 5529 0141 8082 0013 0000 0013 0000 (6d5c) b783 [ 273.477921] ---[ end trace 0000000000000000 ]--- [ 273.482630] Kernel panic - not syncing: Fatal exception in interrupt

In the Linux kernel, the following vulnerability has been resolved: md: fix kmemleak of rdev->serial If kobject_add() is fail in bind_rdev_to_array(), 'rdev->serial' will be alloc not be freed, and kmemleak occurs. unreferenced object 0xffff88815a350000 (size 49152): comm "mdadm", pid 789, jiffies 4294716910 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace (crc f773277a): [<0000000058b0a453>] kmemleak_alloc+0x61/0xe0 [<00000000366adf14>] __kmalloc_large_node+0x15e/0x270 [<000000002e82961b>] __kmalloc_node.cold+0x11/0x7f [<00000000f206d60a>] kvmalloc_node+0x74/0x150 [<0000000034bf3363>] rdev_init_serial+0x67/0x170 [<0000000010e08fe9>] mddev_create_serial_pool+0x62/0x220 [<00000000c3837bf0>] bind_rdev_to_array+0x2af/0x630 [<0000000073c28560>] md_add_new_disk+0x400/0x9f0 [<00000000770e30ff>] md_ioctl+0x15bf/0x1c10 [<000000006cfab718>] blkdev_ioctl+0x191/0x3f0 [<0000000085086a11>] vfs_ioctl+0x22/0x60 [<0000000018b656fe>] __x64_sys_ioctl+0xba/0xe0 [<00000000e54e675e>] do_syscall_64+0x71/0x150 [<000000008b0ad622>] entry_SYSCALL_64_after_hwframe+0x6c/0x74

In the Linux kernel, the following vulnerability has been resolved: block: fix deadlock between bd_link_disk_holder and partition scan 'open_mutex' of gendisk is used to protect open/close block devices. But in bd_link_disk_holder(), it is used to protect the creation of symlink between holding disk and slave bdev, which introduces some issues. When bd_link_disk_holder() is called, the driver is usually in the process of initialization/modification and may suspend submitting io. At this time, any io hold 'open_mutex', such as scanning partitions, can cause deadlocks. For example, in raid: T1 T2 bdev_open_by_dev lock open_mutex [1] ... efi_partition ... md_submit_bio md_ioctl mddev_syspend -> suspend all io md_add_new_disk bind_rdev_to_array bd_link_disk_holder try lock open_mutex [2] md_handle_request -> wait mddev_resume T1 scan partition, T2 add a new device to raid. T1 waits for T2 to resume mddev, but T2 waits for open_mutex held by T1. Deadlock occurs. Fix it by introducing a local mutex 'blk_holder_mutex' to replace 'open_mutex'.

In the Linux kernel, the following vulnerability has been resolved: aoe: fix the potential use-after-free problem in aoecmd_cfg_pkts This patch is against CVE-2023-6270. The description of cve is: A flaw was found in the ATA over Ethernet (AoE) driver in the Linux kernel. The aoecmd_cfg_pkts() function improperly updates the refcnt on `struct net_device`, and a use-after-free can be triggered by racing between the free on the struct and the access through the `skbtxq` global queue. This could lead to a denial of service condition or potential code execution. In aoecmd_cfg_pkts(), it always calls dev_put(ifp) when skb initial code is finished. But the net_device ifp will still be used in later tx()->dev_queue_xmit() in kthread. Which means that the dev_put(ifp) should NOT be called in the success path of skb initial code in aoecmd_cfg_pkts(). Otherwise tx() may run into use-after-free because the net_device is freed. This patch removed the dev_put(ifp) in the success path in aoecmd_cfg_pkts(), and added dev_put() after skb xmit in tx().

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k: delay all of ath9k_wmi_event_tasklet() until init is complete The ath9k_wmi_event_tasklet() used in ath9k_htc assumes that all the data structures have been fully initialised by the time it runs. However, because of the order in which things are initialised, this is not guaranteed to be the case, because the device is exposed to the USB subsystem before the ath9k driver initialisation is completed. We already committed a partial fix for this in commit: 8b3046abc99e ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()") However, that commit only aborted the WMI_TXSTATUS_EVENTID command in the event tasklet, pairing it with an "initialisation complete" bit in the TX struct. It seems syzbot managed to trigger the race for one of the other commands as well, so let's just move the existing synchronisation bit to cover the whole tasklet (setting it at the end of ath9k_htc_probe_device() instead of inside ath9k_tx_init()).

In the Linux kernel, the following vulnerability has been resolved: wifi: wfx: fix memory leak when starting AP Kmemleak reported this error: unreferenced object 0xd73d1180 (size 184): comm "wpa_supplicant", pid 1559, jiffies 13006305 (age 964.245s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 1e 00 01 00 00 00 00 00 ................ backtrace: [<5ca11420>] kmem_cache_alloc+0x20c/0x5ac [<127bdd74>] __alloc_skb+0x144/0x170 [<fb8a5e38>] __netdev_alloc_skb+0x50/0x180 [<0f9fa1d5>] __ieee80211_beacon_get+0x290/0x4d4 [mac80211] [<7accd02d>] ieee80211_beacon_get_tim+0x54/0x18c [mac80211] [<41e25cc3>] wfx_start_ap+0xc8/0x234 [wfx] [<93a70356>] ieee80211_start_ap+0x404/0x6b4 [mac80211] [<a4a661cd>] nl80211_start_ap+0x76c/0x9e0 [cfg80211] [<47bd8b68>] genl_rcv_msg+0x198/0x378 [<453ef796>] netlink_rcv_skb+0xd0/0x130 [<6b7c977a>] genl_rcv+0x34/0x44 [<66b2d04d>] netlink_unicast+0x1b4/0x258 [<f965b9b6>] netlink_sendmsg+0x1e8/0x428 [<aadb8231>] ____sys_sendmsg+0x1e0/0x274 [<d2b5212d>] ___sys_sendmsg+0x80/0xb4 [<69954f45>] __sys_sendmsg+0x64/0xa8 unreferenced object 0xce087000 (size 1024): comm "wpa_supplicant", pid 1559, jiffies 13006305 (age 964.246s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 10 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............ backtrace: [<9a993714>] __kmalloc_track_caller+0x230/0x600 [<f83ea192>] kmalloc_reserve.constprop.0+0x30/0x74 [<a2c61343>] __alloc_skb+0xa0/0x170 [<fb8a5e38>] __netdev_alloc_skb+0x50/0x180 [<0f9fa1d5>] __ieee80211_beacon_get+0x290/0x4d4 [mac80211] [<7accd02d>] ieee80211_beacon_get_tim+0x54/0x18c [mac80211] [<41e25cc3>] wfx_start_ap+0xc8/0x234 [wfx] [<93a70356>] ieee80211_start_ap+0x404/0x6b4 [mac80211] [<a4a661cd>] nl80211_start_ap+0x76c/0x9e0 [cfg80211] [<47bd8b68>] genl_rcv_msg+0x198/0x378 [<453ef796>] netlink_rcv_skb+0xd0/0x130 [<6b7c977a>] genl_rcv+0x34/0x44 [<66b2d04d>] netlink_unicast+0x1b4/0x258 [<f965b9b6>] netlink_sendmsg+0x1e8/0x428 [<aadb8231>] ____sys_sendmsg+0x1e0/0x274 [<d2b5212d>] ___sys_sendmsg+0x80/0xb4 However, since the kernel is build optimized, it seems the stack is not accurate. It appears the issue is related to wfx_set_mfp_ap(). The issue is obvious in this function: memory allocated by ieee80211_beacon_get() is never released. Fixing this leak makes kmemleak happy.

In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: prevent use-after-free on vif when cleaning up all interfaces wilc_netdev_cleanup currently triggers a KASAN warning, which can be observed on interface registration error path, or simply by removing the module/unbinding device from driver: echo spi0.1 > /sys/bus/spi/drivers/wilc1000_spi/unbind ================================================================== BUG: KASAN: slab-use-after-free in wilc_netdev_cleanup+0x508/0x5cc Read of size 4 at addr c54d1ce8 by task sh/86 CPU: 0 PID: 86 Comm: sh Not tainted 6.8.0-rc1+ #117 Hardware name: Atmel SAMA5 unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x34/0x58 dump_stack_lvl from print_report+0x154/0x500 print_report from kasan_report+0xac/0xd8 kasan_report from wilc_netdev_cleanup+0x508/0x5cc wilc_netdev_cleanup from wilc_bus_remove+0xc8/0xec wilc_bus_remove from spi_remove+0x8c/0xac spi_remove from device_release_driver_internal+0x434/0x5f8 device_release_driver_internal from unbind_store+0xbc/0x108 unbind_store from kernfs_fop_write_iter+0x398/0x584 kernfs_fop_write_iter from vfs_write+0x728/0xf88 vfs_write from ksys_write+0x110/0x1e4 ksys_write from ret_fast_syscall+0x0/0x1c [...] Allocated by task 1: kasan_save_track+0x30/0x5c __kasan_kmalloc+0x8c/0x94 __kmalloc_node+0x1cc/0x3e4 kvmalloc_node+0x48/0x180 alloc_netdev_mqs+0x68/0x11dc alloc_etherdev_mqs+0x28/0x34 wilc_netdev_ifc_init+0x34/0x8ec wilc_cfg80211_init+0x690/0x910 wilc_bus_probe+0xe0/0x4a0 spi_probe+0x158/0x1b0 really_probe+0x270/0xdf4 __driver_probe_device+0x1dc/0x580 driver_probe_device+0x60/0x140 __driver_attach+0x228/0x5d4 bus_for_each_dev+0x13c/0x1a8 bus_add_driver+0x2a0/0x608 driver_register+0x24c/0x578 do_one_initcall+0x180/0x310 kernel_init_freeable+0x424/0x484 kernel_init+0x20/0x148 ret_from_fork+0x14/0x28 Freed by task 86: kasan_save_track+0x30/0x5c kasan_save_free_info+0x38/0x58 __kasan_slab_free+0xe4/0x140 kfree+0xb0/0x238 device_release+0xc0/0x2a8 kobject_put+0x1d4/0x46c netdev_run_todo+0x8fc/0x11d0 wilc_netdev_cleanup+0x1e4/0x5cc wilc_bus_remove+0xc8/0xec spi_remove+0x8c/0xac device_release_driver_internal+0x434/0x5f8 unbind_store+0xbc/0x108 kernfs_fop_write_iter+0x398/0x584 vfs_write+0x728/0xf88 ksys_write+0x110/0x1e4 ret_fast_syscall+0x0/0x1c [...] David Mosberger-Tan initial investigation [1] showed that this use-after-free is due to netdevice unregistration during vif list traversal. When unregistering a net device, since the needs_free_netdev has been set to true during registration, the netdevice object is also freed, and as a consequence, the corresponding vif object too, since it is attached to it as private netdevice data. The next occurrence of the loop then tries to access freed vif pointer to the list to move forward in the list. Fix this use-after-free thanks to two mechanisms: - navigate in the list with list_for_each_entry_safe, which allows to safely modify the list as we go through each element. For each element, remove it from the list with list_del_rcu - make sure to wait for RCU grace period end after each vif removal to make sure it is safe to free the corresponding vif too (through unregister_netdev) Since we are in a RCU "modifier" path (not a "reader" path), and because such path is expected not to be concurrent to any other modifier (we are using the vif_mutex lock), we do not need to use RCU list API, that's why we can benefit from list_for_each_entry_safe. [1] https://lore.kernel.org/linux-wireless/ab077dbe58b1ea5de0a3b2ca21f275a07af967d2.camel@egauge.net/

In the Linux kernel, the following vulnerability has been resolved: ACPI: processor_idle: Fix memory leak in acpi_processor_power_exit() After unregistering the CPU idle device, the memory associated with it is not freed, leading to a memory leak: unreferenced object 0xffff896282f6c000 (size 1024): comm "swapper/0", pid 1, jiffies 4294893170 hex dump (first 32 bytes): 00 00 00 00 0b 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace (crc 8836a742): [<ffffffff993495ed>] kmalloc_trace+0x29d/0x340 [<ffffffff9972f3b3>] acpi_processor_power_init+0xf3/0x1c0 [<ffffffff9972d263>] __acpi_processor_start+0xd3/0xf0 [<ffffffff9972d2bc>] acpi_processor_start+0x2c/0x50 [<ffffffff99805872>] really_probe+0xe2/0x480 [<ffffffff99805c98>] __driver_probe_device+0x78/0x160 [<ffffffff99805daf>] driver_probe_device+0x1f/0x90 [<ffffffff9980601e>] __driver_attach+0xce/0x1c0 [<ffffffff99803170>] bus_for_each_dev+0x70/0xc0 [<ffffffff99804822>] bus_add_driver+0x112/0x210 [<ffffffff99807245>] driver_register+0x55/0x100 [<ffffffff9aee4acb>] acpi_processor_driver_init+0x3b/0xc0 [<ffffffff990012d1>] do_one_initcall+0x41/0x300 [<ffffffff9ae7c4b0>] kernel_init_freeable+0x320/0x470 [<ffffffff99b231f6>] kernel_init+0x16/0x1b0 [<ffffffff99042e6d>] ret_from_fork+0x2d/0x50 Fix this by freeing the CPU idle device after unregistering it.

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Fix double free in SMC transport cleanup path When the generic SCMI code tears down a channel, it calls the chan_free callback function, defined by each transport. Since multiple protocols might share the same transport_info member, chan_free() might want to clean up the same member multiple times within the given SCMI transport implementation. In this case, it is SMC transport. This will lead to a NULL pointer dereference at the second time: | scmi_protocol scmi_dev.1: Enabled polling mode TX channel - prot_id:16 | arm-scmi firmware:scmi: SCMI Notifications - Core Enabled. | arm-scmi firmware:scmi: unable to communicate with SCMI | Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 | Mem abort info: | ESR = 0x0000000096000004 | EC = 0x25: DABT (current EL), IL = 32 bits | SET = 0, FnV = 0 | EA = 0, S1PTW = 0 | FSC = 0x04: level 0 translation fault | Data abort info: | ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 | CM = 0, WnR = 0, TnD = 0, TagAccess = 0 | GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 | user pgtable: 4k pages, 48-bit VAs, pgdp=0000000881ef8000 | [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 | Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP | Modules linked in: | CPU: 4 PID: 1 Comm: swapper/0 Not tainted 6.7.0-rc2-00124-g455ef3d016c9-dirty #793 | Hardware name: FVP Base RevC (DT) | pstate: 61400009 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) | pc : smc_chan_free+0x3c/0x6c | lr : smc_chan_free+0x3c/0x6c | Call trace: | smc_chan_free+0x3c/0x6c | idr_for_each+0x68/0xf8 | scmi_cleanup_channels.isra.0+0x2c/0x58 | scmi_probe+0x434/0x734 | platform_probe+0x68/0xd8 | really_probe+0x110/0x27c | __driver_probe_device+0x78/0x12c | driver_probe_device+0x3c/0x118 | __driver_attach+0x74/0x128 | bus_for_each_dev+0x78/0xe0 | driver_attach+0x24/0x30 | bus_add_driver+0xe4/0x1e8 | driver_register+0x60/0x128 | __platform_driver_register+0x28/0x34 | scmi_driver_init+0x84/0xc0 | do_one_initcall+0x78/0x33c | kernel_init_freeable+0x2b8/0x51c | kernel_init+0x24/0x130 | ret_from_fork+0x10/0x20 | Code: f0004701 910a0021 aa1403e5 97b91c70 (b9400280) | ---[ end trace 0000000000000000 ]--- Simply check for the struct pointer being NULL before trying to access its members, to avoid this situation. This was found when a transport doesn't really work (for instance no SMC service), the probe routines then tries to clean up, and triggers a crash.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921e: fix use-after-free in free_irq() From commit a304e1b82808 ("[PATCH] Debug shared irqs"), there is a test to make sure the shared irq handler should be able to handle the unexpected event after deregistration. For this case, let's apply MT76_REMOVED flag to indicate the device was removed and do not run into the resource access anymore. BUG: KASAN: use-after-free in mt7921_irq_handler+0xd8/0x100 [mt7921e] Read of size 8 at addr ffff88824a7d3b78 by task rmmod/11115 CPU: 28 PID: 11115 Comm: rmmod Tainted: G W L 5.17.0 #10 Hardware name: Micro-Star International Co., Ltd. MS-7D73/MPG B650I EDGE WIFI (MS-7D73), BIOS 1.81 01/05/2024 Call Trace: <TASK> dump_stack_lvl+0x6f/0xa0 print_address_description.constprop.0+0x1f/0x190 ? mt7921_irq_handler+0xd8/0x100 [mt7921e] ? mt7921_irq_handler+0xd8/0x100 [mt7921e] kasan_report.cold+0x7f/0x11b ? mt7921_irq_handler+0xd8/0x100 [mt7921e] mt7921_irq_handler+0xd8/0x100 [mt7921e] free_irq+0x627/0xaa0 devm_free_irq+0x94/0xd0 ? devm_request_any_context_irq+0x160/0x160 ? kobject_put+0x18d/0x4a0 mt7921_pci_remove+0x153/0x190 [mt7921e] pci_device_remove+0xa2/0x1d0 __device_release_driver+0x346/0x6e0 driver_detach+0x1ef/0x2c0 bus_remove_driver+0xe7/0x2d0 ? __check_object_size+0x57/0x310 pci_unregister_driver+0x26/0x250 __do_sys_delete_module+0x307/0x510 ? free_module+0x6a0/0x6a0 ? fpregs_assert_state_consistent+0x4b/0xb0 ? rcu_read_lock_sched_held+0x10/0x70 ? syscall_enter_from_user_mode+0x20/0x70 ? trace_hardirqs_on+0x1c/0x130 do_syscall_64+0x5c/0x80 ? trace_hardirqs_on_prepare+0x72/0x160 ? do_syscall_64+0x68/0x80 ? trace_hardirqs_on_prepare+0x72/0x160 entry_SYSCALL_64_after_hwframe+0x44/0xae

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Don't issue ATS Invalidation request when device is disconnected For those endpoint devices connect to system via hotplug capable ports, users could request a hot reset to the device by flapping device's link through setting the slot's link control register, as pciehp_ist() DLLSC interrupt sequence response, pciehp will unload the device driver and then power it off. thus cause an IOMMU device-TLB invalidation (Intel VT-d spec, or ATS Invalidation in PCIe spec r6.1) request for non-existence target device to be sent and deadly loop to retry that request after ITE fault triggered in interrupt context. That would cause following continuous hard lockup warning and system hang [ 4211.433662] pcieport 0000:17:01.0: pciehp: Slot(108): Link Down [ 4211.433664] pcieport 0000:17:01.0: pciehp: Slot(108): Card not present [ 4223.822591] NMI watchdog: Watchdog detected hard LOCKUP on cpu 144 [ 4223.822622] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S OE kernel version xxxx [ 4223.822623] Hardware name: vendorname xxxx 666-106, BIOS 01.01.02.03.01 05/15/2023 [ 4223.822623] RIP: 0010:qi_submit_sync+0x2c0/0x490 [ 4223.822624] Code: 48 be 00 00 00 00 00 08 00 00 49 85 74 24 20 0f 95 c1 48 8b 57 10 83 c1 04 83 3c 1a 03 0f 84 a2 01 00 00 49 8b 04 24 8b 70 34 <40> f6 c6 1 0 74 17 49 8b 04 24 8b 80 80 00 00 00 89 c2 d3 fa 41 39 [ 4223.822624] RSP: 0018:ffffc4f074f0bbb8 EFLAGS: 00000093 [ 4223.822625] RAX: ffffc4f040059000 RBX: 0000000000000014 RCX: 0000000000000005 [ 4223.822625] RDX: ffff9f3841315800 RSI: 0000000000000000 RDI: ffff9f38401a8340 [ 4223.822625] RBP: ffff9f38401a8340 R08: ffffc4f074f0bc00 R09: 0000000000000000 [ 4223.822626] R10: 0000000000000010 R11: 0000000000000018 R12: ffff9f384005e200 [ 4223.822626] R13: 0000000000000004 R14: 0000000000000046 R15: 0000000000000004 [ 4223.822626] FS: 0000000000000000(0000) GS:ffffa237ae400000(0000) knlGS:0000000000000000 [ 4223.822627] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 4223.822627] CR2: 00007ffe86515d80 CR3: 000002fd3000a001 CR4: 0000000000770ee0 [ 4223.822627] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 4223.822628] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 [ 4223.822628] PKRU: 55555554 [ 4223.822628] Call Trace: [ 4223.822628] qi_flush_dev_iotlb+0xb1/0xd0 [ 4223.822628] __dmar_remove_one_dev_info+0x224/0x250 [ 4223.822629] dmar_remove_one_dev_info+0x3e/0x50 [ 4223.822629] intel_iommu_release_device+0x1f/0x30 [ 4223.822629] iommu_release_device+0x33/0x60 [ 4223.822629] iommu_bus_notifier+0x7f/0x90 [ 4223.822630] blocking_notifier_call_chain+0x60/0x90 [ 4223.822630] device_del+0x2e5/0x420 [ 4223.822630] pci_remove_bus_device+0x70/0x110 [ 4223.822630] pciehp_unconfigure_device+0x7c/0x130 [ 4223.822631] pciehp_disable_slot+0x6b/0x100 [ 4223.822631] pciehp_handle_presence_or_link_change+0xd8/0x320 [ 4223.822631] pciehp_ist+0x176/0x180 [ 4223.822631] ? irq_finalize_oneshot.part.50+0x110/0x110 [ 4223.822632] irq_thread_fn+0x19/0x50 [ 4223.822632] irq_thread+0x104/0x190 [ 4223.822632] ? irq_forced_thread_fn+0x90/0x90 [ 4223.822632] ? irq_thread_check_affinity+0xe0/0xe0 [ 4223.822633] kthread+0x114/0x130 [ 4223.822633] ? __kthread_cancel_work+0x40/0x40 [ 4223.822633] ret_from_fork+0x1f/0x30 [ 4223.822633] Kernel panic - not syncing: Hard LOCKUP [ 4223.822634] CPU: 144 PID: 1422 Comm: irq/57-pciehp Kdump: loaded Tainted: G S OE kernel version xxxx [ 4223.822634] Hardware name: vendorname xxxx 666-106, BIOS 01.01.02.03.01 05/15/2023 [ 4223.822634] Call Trace: [ 4223.822634] <NMI> [ 4223.822635] dump_stack+0x6d/0x88 [ 4223.822635] panic+0x101/0x2d0 [ 4223.822635] ? ret_from_fork+0x11/0x30 [ 4223.822635] nmi_panic.cold.14+0xc/0xc [ 4223.822636] watchdog_overflow_callback.cold.8+0x6d/0x81 [ 4223.822636] __perf_event_overflow+0x4f/0xf0 [ 4223.822636] handle_pmi_common ---truncated---

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btrtl: fix out of bounds memory access The problem is detected by KASAN. btrtl driver uses private hci data to store 'struct btrealtek_data'. If btrtl driver is used with btusb, then memory for private hci data is allocated in btusb. But no private data is allocated after hci_dev, when btrtl is used with hci_h5. This commit adds memory allocation for hci_h5 case. ================================================================== BUG: KASAN: slab-out-of-bounds in btrtl_initialize+0x6cc/0x958 [btrtl] Write of size 8 at addr ffff00000f5a5748 by task kworker/u9:0/76 Hardware name: Pine64 PinePhone (1.2) (DT) Workqueue: hci0 hci_power_on [bluetooth] Call trace: dump_backtrace+0x9c/0x128 show_stack+0x20/0x38 dump_stack_lvl+0x48/0x60 print_report+0xf8/0x5d8 kasan_report+0x90/0xd0 __asan_store8+0x9c/0xc0 [btrtl] h5_btrtl_setup+0xd0/0x2f8 [hci_uart] h5_setup+0x50/0x80 [hci_uart] hci_uart_setup+0xd4/0x260 [hci_uart] hci_dev_open_sync+0x1cc/0xf68 [bluetooth] hci_dev_do_open+0x34/0x90 [bluetooth] hci_power_on+0xc4/0x3c8 [bluetooth] process_one_work+0x328/0x6f0 worker_thread+0x410/0x778 kthread+0x168/0x178 ret_from_fork+0x10/0x20 Allocated by task 53: kasan_save_stack+0x3c/0x68 kasan_save_track+0x20/0x40 kasan_save_alloc_info+0x68/0x78 __kasan_kmalloc+0xd4/0xd8 __kmalloc+0x1b4/0x3b0 hci_alloc_dev_priv+0x28/0xa58 [bluetooth] hci_uart_register_device+0x118/0x4f8 [hci_uart] h5_serdev_probe+0xf4/0x178 [hci_uart] serdev_drv_probe+0x54/0xa0 really_probe+0x254/0x588 __driver_probe_device+0xc4/0x210 driver_probe_device+0x64/0x160 __driver_attach_async_helper+0x88/0x158 async_run_entry_fn+0xd0/0x388 process_one_work+0x328/0x6f0 worker_thread+0x410/0x778 kthread+0x168/0x178 ret_from_fork+0x10/0x20 Last potentially related work creation: kasan_save_stack+0x3c/0x68 __kasan_record_aux_stack+0xb0/0x150 kasan_record_aux_stack_noalloc+0x14/0x20 __queue_work+0x33c/0x960 queue_work_on+0x98/0xc0 hci_recv_frame+0xc8/0x1e8 [bluetooth] h5_complete_rx_pkt+0x2c8/0x800 [hci_uart] h5_rx_payload+0x98/0xb8 [hci_uart] h5_recv+0x158/0x3d8 [hci_uart] hci_uart_receive_buf+0xa0/0xe8 [hci_uart] ttyport_receive_buf+0xac/0x178 flush_to_ldisc+0x130/0x2c8 process_one_work+0x328/0x6f0 worker_thread+0x410/0x778 kthread+0x168/0x178 ret_from_fork+0x10/0x20 Second to last potentially related work creation: kasan_save_stack+0x3c/0x68 __kasan_record_aux_stack+0xb0/0x150 kasan_record_aux_stack_noalloc+0x14/0x20 __queue_work+0x788/0x960 queue_work_on+0x98/0xc0 __hci_cmd_sync_sk+0x23c/0x7a0 [bluetooth] __hci_cmd_sync+0x24/0x38 [bluetooth] btrtl_initialize+0x760/0x958 [btrtl] h5_btrtl_setup+0xd0/0x2f8 [hci_uart] h5_setup+0x50/0x80 [hci_uart] hci_uart_setup+0xd4/0x260 [hci_uart] hci_dev_open_sync+0x1cc/0xf68 [bluetooth] hci_dev_do_open+0x34/0x90 [bluetooth] hci_power_on+0xc4/0x3c8 [bluetooth] process_one_work+0x328/0x6f0 worker_thread+0x410/0x778 kthread+0x168/0x178 ret_from_fork+0x10/0x20 ==================================================================

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_core: Fix possible buffer overflow struct hci_dev_info has a fixed size name[8] field so in the event that hdev->name is bigger than that strcpy would attempt to write past its size, so this fixes this problem by switching to use strscpy.